R911374271 (HCS01.1E-W0008-A-03-B-ET-EC-EP-NN-NN-FW)

Name: R911374271 (HCS01.1E-W0008-A-03-B-ET-EC-EP-NN-NN-FW)
Brand: Indramat Drives
SKU: HCS01.1E-W0008-A-03-B-ET-EC-EP-NN-NN-FW
Price: 483.00 USD

HCS IndraDrive Controllers

Call for Quote

Expedited Lead Times on Select Parts
1 Year Warranty Included
Free Ground Shipping

Phone

Part Number

+Add a message

Message

Request a Replacement

Request a Repair

Quote Both

Expedited Lead Times on Select Parts
1 Year Warranty Included
Free Ground Shipping

Phone:
1-888-551-3082

Email:
sales@indramat-usa.com

The R911374271 (HCS01.1E-W0008-A-03-B-ET-EC-EP-NN-NN-FW) is an HCS drive controller engineered for use with three-phase AC power from 200 to 500 V (±10%), featuring a peak output current of 8 A. It incorporates a BASIC control section design (version 1), internal air cooling via an integrated blower (56 m³/h), and an IP20 enclosure rating. Key interfaces include Multi-Ethernet communication and a multi-encoder interface supporting IndraDyn, Hiperface, and EnDat 2.1/2.2. The unit provides a slot for an optional safety module and allows the integration of an engineering port module. Firmware is not included and must be specified separately. Operation is supported within an ambient temperature range of 0–40 °C (with restrictions up to 55 °C). Control panel is standard, non-hot plug. Only qualified personnel should install or operate this device.

Technical Specifications

Power Supply
Feeding Type

Control Section
Basic

Maximum Current Output
8 Amps

Input Voltage Range
200 to 500 Volts AC (Three-Phase)

Cooling
Forced Ventilation

Volumetric Cooling Capacity
56 m3/h

Cool Inlet
Located at Bottom of Unit

Cool Outlet
Located at Top of Unit

Communication
Integrated Multi-Ethernet

Safety Module
Vacant Slot

Control Panel
Standard

Firmware
Depends on Installed Firmware

User Requirement
Only Qualified Personnel Should Handle and Operate

Frequently Asked Questions

How does the HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW integrate into plant networks?

It uses MultiEthernet to interface directly with a variety of Ethernet-based controllers and supervisory systems, reducing protocol conversion. Proper network planning such as VLAN segregation and QoS helps prioritize motion traffic and keep latency low.

What are best practices for ventilation when installing HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW?

Provide filtered cabinet intake and ensure the blower’s airflow path is unobstructed; allow clearance for service access. Regularly inspect and clean inlet filters and the blower to prevent heat buildup and preserve consistent thermal performance.

What does IP20 imply about the operating environment of HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW?

IP20 is intended for indoor, cabinet-protected environments and does not guard against moisture or very fine particles. For dusty or wet production areas, mount the drive in a sealed enclosure or add environmental protection to the cabinet.

What should teams document when deploying HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW?

Record firmware versions, parameter baselines, safety wiring diagrams and functional test results for STO and SBC. Thorough documentation simplifies future updates, audits and troubleshooting while maintaining traceability for safety activities.

What commissioning checks validate HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW performance?

Verify encoder feedback, brake actuation timing, thermal behavior under load and network determinism. Capture baseline parameters and test results to support repeatable deployments.

Common Misspellings

HCS011EW0008A03BETECEPNNNNFW

HCS01 1E W0008 A 03 B ET EC EP NN NN FW

hcs01.1e-w0008-a-03-a-cc-ec-da-nn-nn-fw

HCS1.1E-W0008-A-03-B-ET-EC-EP-NN-NN-FW

Internal Product Review

Bosch Rexroth's HCS01.1E-W0008-A-03-B-ET-EC-EP-L4-NN-FW emphasises dual-layer stopping via electronic torque cut and brake control while keeping compact cabinet-friendly dimensions. It is aimed at systems where minimal panel real estate are critical requirements for safe operation.