R911262035 (MDD090C-N-030-N2L-130PB1)

Name: R911262035 (MDD090C-N-030-N2L-130PB1)
Brand: Indramat Motors
SKU: MDD090C-N-030-N2L-130PB1
Price: 225.00 USD
Availability: InStock
Rating: 4.7 (14 reviews)

MDD Synchronous Motors

Rated 4.7 stars (14 total reviews)

Front Right

In-Stock, Ships 3-5 Days

Expedited Lead Times on Select Parts
1 Year Warranty Included
Free Ground Shipping

Phone

Part Number

+Add a message

Message

Request a Replacement

Request a Repair

Quote Both

Expedited Lead Times on Select Parts
1 Year Warranty Included
Free Ground Shipping

Phone:
1-888-551-3082

Email:
sales@indramat-usa.com

The R911262035 (MDD090C-N-030-N2L-130PB1) is a servo motor engineered for precise automation applications, featuring a standard housing with a corrosion-resistant coating. It delivers a continuous torque at standstill of 10.4 Nm, nominal speed of 3000 min⁻¹, and utilizes digital servo feedback (DSF) for position control. The unit includes a blocking brake with 6.5 Nm holding torque, standard balancing, a centering diameter of 130 mm, and a keyway shaft with shaft seal. An optional air blower can augment surface cooling during frequent start-stop cycles. The motor employs grease-lubricated ball bearings rated for approximately 30,000 hours under normal load conditions. Electrical connection is via a connector on Side B; shaft end configuration is standard with no rear extension.

Technical Specifications

Type
Servo Motor

Design
Housing unit

Operational Efficiency
95%

Protection System
Prime Coat against Corrosive Substances

Temperature Transmission System
Present

Cooling Required
Additional Air Blower for Start-Stop Operations

Output Shaft
Designed with special Keyway

Bearings
Special Grease-Lubricated Ball Bearings

Bearings Service Life
30,000 hours

Frequently Asked Questions

What trade-offs come from “standard balancing” for a rotor in high-speed applications?

Standard balancing is adequate for many duties, but for very high-speed or low-vibration systems, you may demand higher balance class (e.g. G2.5 or better) to reduce bearing loads and resonance.

In what cases is the centering diameter of 130 mm (flange interface) critical for integration?

The 130 mm centering diameter defines how the motor mates to machine frames or gearboxes; precise alignment and bearing preload depend on this interface to avoid misalignment loads.

What installation or alignment tolerances matter for the side-B connector orientation?

Since the connector is on side B, cable routing must avoid interference; also maintain angular and radial alignment to avoid stress on the connector pins during assembly.

How is commutation performance affected if rotor inertia or load inertia is much higher than expected?

A mismatch between motor and load inertia reduces servo bandwidth and can lead to oscillation or slower settling, so keep the total reflected inertia reasonably matched (e.g. ≤ 10× motor’s rotor inertia).

How would you refer to this motor in a technical support query using its exact model and manufacturer?

Use “Bosch Rexroth MDD090C-N-030-N2L-130PB1” when requesting firmware, support, or spares to ensure precise identification.

Common Misspellings

MDD-090C-N-030-N2L-130PB1

MDD090C N 030 N2L 130PB1

MDD090C-N-030-N2L-130-PB1

MDD090CN030N2L130PB1

MDD90C-N-030-N2L-130PB1

MDDO90C-N-030-N2L-130PB1

MDDO9OC-N-O3O-N2L-13OPB1

mdd090c-n-030-n2l-130pb1

Internal Product Review

The MDD090C-N-030-N2L-130PB1 motor from Bosch Rexroth includes a 6.5 Nm holding brake and a keyway shaft with a shaft seal. It offers 10.4 Nm continuous torque at a nominal speed of 3000 min⁻¹ and uses digital servo feedback. This motor is suitable for use in robotics, packaging, and textile machinery.